ESSS INPUT MESSAGES
===================


*
   
     
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
#1a ESSNOTES
   
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
    
    
t-tnn-dg00xxxxxx.to dgn a tnn,where x=tnn
t-tnn-rs00xxxxxx.to request status of tnn
t-tnn-mi00xxxxxx.to make idle tnn
t-tnn-mb00xxxxxx.to make busy tnn
t-tnn-tt17xxxxxx.to perform 105tl test on tnn
t-jnn-dgxxxxxx.to dgn jnctr,if tok will ma
   
trk-group-mb00xxxx.to mb entire tgn,where x=tgn
trk-group-lo00xxxx.to lockout entire group
trk-group-ma00xxxx.to make active entire group
trk-group-lt00xxxx.to list tnn's of entire group
(note: the letters gro may be used in lieu of group)
     
test-trk-17xxxxxx 105 y yyy 7617558.
test-trk-07xxxxxx 102 y yyy 7617558.
   
trk-list-sos.
trk-list-mos.
trk-list-jos.
trk-list-dos.
   
vfy-tnn-11xxxxxx.
vfy-tgn-14xxx.
    
    
net-tnn-xxxxxx.to trace held tnn
net-line-yyyyyyy0000.to trace line where y=tn
net-line-yyyyyyyzzzz.to trace line where y=tn and z=term#
t-dn-rdxxxxxxx.to read line: 0=idle  1=busy
   
alw:rcchan sc2!to allow rc on smtc use sc1 for mtc
vfy-tkgn-07 xxx.to run trunk inventory, use filter.
f:ns42e.smtc;pat tr10,from 0830;odt <filename>!
t-tnn-rt00 diag xxxxxx.repeat test (01 bsy,02 sync,05 cont.pol)

    
DIAGNOSTIC TBLS
-3540open or shorted
-0120reversal
-0010no wink
-0453no wink
-0001line seizure
-0100def trunk unit
-3446no trunk unit
-0002constant ringing
-0020PSAP mult wink,didnt complete,low level,etc
-0004PSAP tone on more than 1 sec
    
   
   
    
   
   
   
   
   
   
   
   
**********TO VFY AND RELEASE HELD LINE**********
   
   
   
1.t-dn-rdxxxxxxx.0=idle 1=busy
   
2.net-line-xxxxxxx0000.trace line for tnn
net-line-xxxxxxxyyyy.
   
  first 2 numbers of trace: 00 or 20=idle  40=hi/wet
  
3.t-tnn-rs00xxxxxx.check tg of tnn being held
   
4.tag-tnn-pmtxxxxxx.where x=tnn
   
5.obtain cs address from tr21 printout:
tr 21 pmt xxxxxxx=tnn
yyyyyyyy=cs address
   
6.load:cs,adr yyyyyyy:0!                      (BE CAREFUL OF ADDRESS!)
   
7.wait aprox. 5min then recheck
   
     
     
     
     

   
lt-list-crc.<to clear rc list
   
lt-list-clr.<to clear llr list
   
rst:ious x,iouc y!<to restore ious/iouc
   
aud:erapdata init!<to clear erap buffer
   
u:coco erap!to clear erap in all ofcs
   
iam-idle-xx yy.<to idle ra
   
dtf-req-rst001.<to rst dtf 00 1
   
dtf-req-dgn001.<
  
clk-advance-xxx.<to advance clock xxx seconds
   
alt-sta-dga(dn)****.<to alit line
 
  puc-status-xx.
  puc- - yy rst z xxx.                  yy=puc mbr   z=controller
 
  dtrm-req-rst xxxx.to restore dtrm xxxx
  
  psg-p-dry.to list all mb oe's
 
  rt-req-2.to rst rt0
  rt-req-3.to rst rt1
   
   
   
   
   
   
   
   
   
***** LINENOTES *****
vfy-dn-30 xxxxxxx.<to vfy dn
  
vfy-len-31 xx xxx xxx.<to vfy len
  
vfy-cstg-36 xxxx.<to vfy mlhg & od list
  
vfy-cstg-34 xxxx.<to vfy mlhg head table
  
vfy-list-09 xxxxxxx yy 0000.<to vfy sc list: x=dn
y=02 for sc1
y=20,28,36 for sc2
y=1st digit of 8 on po
11=* on the p/o
  
v-sfgn-xxxx.<
  vf:dnsvy:dn xxxxxxx,1 featrs,pic!to vfy features

$ 

*
   
   
#2ess notes
   
a vy l/
tn xxx xxxx!<to vfy a dn
   
a vy l/
oe xx xxxx!to vfy a oe
   
m hd pr!<to print hi and dri list
   
a vy mlh xx y!<to vfy mlhg and term
   
a vy mlh xx!<to vfy mlhg
   
a l trc xxx xxxx!<to trc a dn
   
a ml trc xx y!<to trc mlhg and term
   
m l rst xx xxxx yyy yyyy!<to rst line x=oe y=dn
   
m l rmv xx xxxx yyy yyyy!<to remv line x=oe y=dn
   
mh l idl xx xxxx yyy yyyy!<hi priorty idle of line
   
m tk rst xxx yyy!<to rst trk
  
mh tk rst xxx yyy!<to rst trk hi priority
   
m tk si!<to pull oos list trunks
   
m tk dgn xxx yyy!<to dgn trunk
   
m tk rmv xxx yyy!<to remove trunk
   
m sv rst xxx yyy!<to rst svc trk
   
m nw rst xxx yyy!<
   
  a cf pr!<to print call fwd list
  
  m cu rst!<to restore cu (int dis)2aess
  rst:cu!<to restore cu in 2bess
 
  op:clk!to output time
  set:clk:time hh mi ss!<to set time
  m tt tim hh mi sec!to set time in plcs
 
  m sy prt alm!<to op alarms
 
  op:dl,stat;all!<
  rst:dl,eadas(0,0);ucl!<to rst eadas chan osh
 
  M CW CARD                             this output says the ofc is writing card
s
 
  
mh tk rst xxx yyy!<to ucl trk up
   
m:cu rst!<to restore cu (int dis)
cu may be up but oo sync

$ 

   
   
#3ess notes
   
   
ver:line tn xxx xxxx!to vfy tel no.
   
ver:line oe yy yyyy!to vfy oe
   
rmv:line yy yyyy 749 xxxx!to bsy out line
   
rst:line yy yyyy 749 xxxx!to restore line
   
trc:tn 749 xxxx!to trace line
   
op:line:stat!to print hi and wet list
   
op:trk!to print trk oos list
   
op:svc!to print svc trk oos list
   
dgn:trk xxx xxx!to dgn trk
   
dgn:svc xxx xxx!to dgn svc trk
   
rst:trk xxx xxx!to rst trunk
rst:trk xxx xxx;ucl!
   
rmv:svc xxx xxx!to remove svc trk
   
dgn:trk xxx xxx,oto!to dgn trunk ofc to ofc
   
rst:jc xxx xxx!to restore junctor
   
rpt:trbl;cont!
   
ver:cfn:tn 749 xxxx!
 
au:maint!to op oos list
 
op:alm:stat!to op alarms
 
USE RC:SP! FORMAT TO CHANGE ALARMS
ver:cfn:tn 749 xxxx!<to vfy call fwding number
   

   
    
    
   
WHEN TRK IS HELD TO TKGMN 140 001
dump:st 47136!
word 36 37 40 41 42 43 44 45
lod:st 471xx!       xx=word # with other than all 0000 0000
dmp:st 47136,19!
ALL 19 WORDS SHOULD BE ALL BALLS
$ 



   
   
#5ess notes
        ******************************
   
   
rst:trk,tkgmn=xxx-yyy,oos,dsbld<
   
rmv:trk,tkgmn=xxx-yyy<
   
tst:trk,den=a-b-c-d,type=105<
   
op:status,ten=a-b-c-d<
   
op:status,dn=6369090<
   
rst:trk,tkgmn=xxx-yyy&&zzz<       x=tgn y=start mbr z=end mbr
   
rmv:trk,tkgmn=xxx-yyy,oos,cadn,ucl<
   
rst:trk,tkgmn=xxx-yyy,ucl<
   
op:list,trunks,oos<
   
rst:line,dn=xxxxxxx,oos,dsbld<
  
rmv:line,dn=xxxxxxx<
   
sw:s96,fac=<sid>-<shelf>,prot,<state>;    (state=on or off)
   
cfr:s96,fac=<sid>-<shelf>,felp,<state>;
   
op:s96,sid=xxxx;
 
set:clock,increase=xx;                        increase in seconds
 
init:am,okp,spp,pid=2;                        to reinit alit
    
trc:ipct,dn=xxxxxxx;to trace call
 
SUPERKILL******
EA page  42,parameter 3,50
 
 
 
 
 
   
TO CLEAR FILESYS CRIT OFV
****************************************
    
    

1.) op:status:data,listdir,fn="/cdmp"<
                           dn="/cdmp"<          use dn for tsvl
   
   
2.) determine which file is overflowing.
   
   
3.) clr:filesys:data,file,fn="/cdmp/filename"<
   
 
 
 
 
 
wheeeeeeeeee have fun
dark call